Specifying an Electrical Safety Package for a Substation Retrofit

November 4, 2026 7 min readProcurement & Export

Retrofit safety gear usually gets bought item by item, and the ratings stop matching. Five functional groups, the fields worth writing into the requisition, and the documents that have to travel with the crate.

A substation retrofit almost never fails on the switchgear. It fails three weeks before energisation, when somebody opens the crate and finds that the earthing set is rated for a fault level the site no longer has, or that the gloves bought for the 11 kV panel are Class 1 because that was what the last project ordered.

The package was never specified as a package. It was assembled from six purchase orders, each written against its own product, none of them written against the work method.

This piece is about writing the one document that prevents that.

1. Start from the switching schedule, not the product list

The order of operations matters more than the catalogue does. A retrofit safety package is defined by three questions, in this order:

  1. 1What work is being done live, and what is being done dead? Live work sets the glove class and the mat class. Dead work sets what the earthing and short-circuiting has to handle.
  2. 2What is the prospective fault current and the protection clearing time? Not the system voltage. This is the number the earthing set is actually rated against.
  3. 3Who is doing the work, and with what tooling? A contractor crew and a permanent O&M team need different tool control, and possibly different fall protection.

Get those three answered and most of the specification writes itself. Skip them and you will be specifying from a catalogue, which is how the crate arrives wrong.

2. The five functional groups

Every package I have quoted for a retrofit falls into five groups. The boundaries matter more than the item count, because a gap between two groups is what gets discovered on site.

Insulation, portable. Insulating matting to IEC 61111 or ASTM D178, class selected by maximum use voltage. Gloves to IEC 60903 or ASTM D120, class selected the same way, with the leather protector rule applied — where a glove is worn without protectors, the class goes up by one, Class 00 and Class 0 excepted. The cuff has to overlap the sleeve by 12 mm at Class 00/0, 25 mm at Class 1, 50 mm at Class 2, 75 mm at Class 3 and 100 mm at Class 4.

Voltage detection. Detectors to IEC 61243. Which part depends on the type: Part 1 is capacitive, above 1 kV a.c.; Part 2 is resistive, 1 kV to 36 kV a.c.; Part 5 covers voltage detecting systems from 1 kV to 52 kV. A detector and the matting next to it can both be "for 11 kV" and still be specified against different standards — that is normal, not an error.

Earthing and short-circuiting. Portable sets to IEC 61230. This is the group most often specified wrongly, because the standard gives no rated voltage at all: the withstand capability is rated by current, time and peak factor. A purchase order written as "33 kV earthing set" names the wrong variable. Send the prospective fault current and the clearing time instead — the reasoning is here.

Tool control. Whether that is a smart cabinet or a simpler shadow board, the control objective is the same: nothing leaves the store without a name against it, and every item is returned. In a retrofit this group is usually added late and ends up as a shelf in a container.

Fall protection. Harness to EN 361; a complete fall-arrest system falls under EN 363, and body-support types under EN 358, EN 813 and EN 1497. If the retrofit includes work at height on the gantry, this group is not optional.

3. The fields that decide whether the crate is right

For each group, these are the fields where an omission costs money. They are worth listing explicitly in the requisition rather than leaving to the supplier's default.

  • Insulating matting: standard and edition, class, thickness (a window under IEC, a nominal plus tolerance under ASTM), surface finish, roll or cut-sheet dimensions
  • Gloves: standard, class, Type (I or II) or Category letter, size, and whether leather protectors are being supplied with them
  • Detectors: IEC 61243 part number, voltage range, indoor or outdoor, IP rating
  • Earthing sets: rated current, rated time, peak factor, conductor material and cross-section, clamp type for the actual terminal geometry
  • Tool control: capacity, access method, whether usage records need to be exported
  • Fall protection: harness standard, system type, lanyard type, and whether restraint or arrest

The single most expensive omission in this list is the clamp type on the earthing set. It is also the least frequently specified. The set arrives, and the clamps do not fit the bushings on a 1980s panel.

4. Voltages that do not line up across items

A package has an internal consistency problem that no single product page can warn you about. Three examples that recur:

  • AC and DC are different columns. A glove rated 17 kV a.c. is 25.5 kV d.c. — the DC figure is 1.5 times the AC one, and it is published, not calculated. If part of the retrofit is on a DC system — battery plant, traction, HVDC — the AC numbers on the other items in the package do not transfer.
  • Class does not follow thickness. At the same class, IEC asks 3 mm and ASTM asks 6.4 mm for Class 2. A package mixing the two thickness conventions will look inconsistent at goods-in and be consistent in fact. Say which standard each line is bought to, on the line.
  • Matting class and glove class are chosen independently. Both are set by maximum use voltage, but the glove is set by what the hand touches and the mat by where the feet stand. They can legitimately differ by a class, and usually do.

5. The documents that travel with the package

Ask for these at the requisition stage, not after the ship date:

  • Batch dielectric test report for the matting and the gloves, one per batch
  • Type test report for the earthing set, showing rated current and rated time
  • Test report or declaration for the detectors against the named IEC 61243 part
  • Declaration of conformity for the harness against EN 361
  • Packing list that maps every document to a line item on the order

The last one is what makes an inspection go quickly. A folder of reports that cannot be matched to the crate is a folder the inspector will not accept.

6. A requisition template that survives review

Seven lines per item, and the package builds itself:

  1. 1Item and quantity
  2. 2Standard and edition
  3. 3Class or rating, with the figure it was derived from (system voltage, fault current, clearing time)
  4. 4Dimensions, size or capacity
  5. 5Material or Type / Category
  6. 6Test document required
  7. 7Tag or location the item is destined for

Line 3 is the one that separates a requisition from a shopping list, because it records why the rating was chosen. When the design changes — and on a retrofit it does — the affected lines can be re-derived instead of re-guessed.

7. Retrofit-specific traps

Three things that come up on brownfield sites and rarely on new build:

  • The nameplate is not the system voltage. Old panels are frequently operated at a lower voltage than they were built for, or have been re-fed. Confirm the actual operating voltage with the network operator before it drives the class selection.
  • Existing earthing points are the wrong geometry. Even when the fault level is fine, the clamps may not attach. Ask for a photo of the terminal before the PO goes out.
  • Two standards on one site. A retrofit often inherits an ASTM-specified store and adds IEC-specified equipment. Either is fine; mixing them within one work method is not, because the retest intervals and the thickness conventions differ.

8. What we supply

We have been building this kind of package since 1996, across more than 5,000 projects in 60-plus countries. The plant covers 1,200,000 m² of site with 80,000 m² of building area and seven production lines, so matting, gloves, detectors, earthing sets and tool cabinets come from the same production base rather than six trading intermediaries.

Send us the switching schedule and the fault level, and we will come back with a line-by-line package — the standards, the classes, the thicknesses, and the test documents that will travel with each crate. If a line in your existing requisition does not resolve to a rating, we will tell you which figure is missing rather than guess it.

Need this confirmed against your own installation?

Send us the network voltage, the standard you are specifying against and the ambient conditions. Our engineers will confirm the class, thickness and test report, and reply with lead time.

Ask a technical question
Start Your Project

Let's build your power infrastructure together

Send us your specifications — insulating mats, gloves, voltage detectors, grounding systems or safety tooling projects. Our engineers respond within 24 hours with technical recommendations and pricing.